[Free] 2018(Jan) Latesttests Passguide Oracle 1z0-404 Dumps with VCE and PDF 31-40

Latesttests
2018 Jan Oracle Official New Released 1z0-404
100% Free Download! 100% Pass Guaranteed!
http://www.Latesttests.com/1z0-404.html

Oracle Communications Session Border Controller 7 Basic Implementation Essentials

Question No: 31

Which three options are valid ways to apply Header Manipulation Rules (HMRs) to your existing configuration?

  1. Navigate to the network-interface configuration element and configure the in- manipulationid parameter.

  2. Navigate to the session-agent configuration element and configure the in-manipulationid parameter.

  3. Navigate to the sip-interface configuration element and configure the in-manipulationid parameter.

  4. Navigate to the session-agent configuration element and configure the in-manipulationid parameter.

  5. Navigate to the session-group configuration element and configure the in-manipulationid parameter.

Answer: A,B,C

Question No: 32

The Session Border Controller is not routing calls to a specific SIP endpoint from the backbone realm to the access realm in an Access-Backbone architecture.

How can you troubleshoot this routing issue?

  1. by running the notify berpd force command

  2. by running the show sipd endpoint-ip lt;phone numbergt; command

  3. by checking the sip-manipulation configuration element used for routing from the backbone realm to the access realm

  4. by checking the registration-cache configuration element used for routing from the access realm to the backbone realm

  5. by checking the local-policy configuration element used for routing from the access realm to the backbone realm

Answer: D

Question No: 33

Which two statements are true about a realm on the Session Border Controller?

  1. It can only have one steering poolport per realm.

  2. It is a layer 3 abstraction of a VoIP network.

  3. It is a logical definition of a network or group of networks comprising devices that provide real-time communication.

  4. It is a layer 5 abstraction of a VoIP network.

  5. It is acollection of IP devices that perform IP routing functions.

Answer: B,C

Question No: 34

What is the first thing you must do when setting up the boot parameters of the Session Border Controller?

  1. reset thesystem clock

  2. know the superuser mode password and access the configuration mode

  3. disable FTP access to the wancom0 management interface

  4. obtain the bootparam license

  5. verify the configuration by executing the verify-config command

Answer: D

Question No: 35

What two problems do Network Address Translations (NATs)introduce into VoIP networks? (Choose two.)

  1. There are no major concerns with NATs.

  2. NATs block unsolicited incoming signaling and media.

  3. NATs block unsolicited incoming signaling but allow incoming media.

  4. NATs pinholes expire after aconfigurable time.

  5. NATs devices can be overloaded by incoming registrations.

Answer: D,E

Question No: 36

Where are passwords and licensing information stored?

  1. Non-Volatile Random Access Memory (NVRAM)

  2. Content Addressable Memory (CAM)

  3. RAMmemory

  4. Synchronous Dynamic Random Access Memory (SDRAM)

  5. Boot Flash

Answer: A

Question No: 37

How doesthe Session Border Controller ensure that a pinhole is kept open for persistent communication to a SIP endpoint behind a NAT device?

  1. by changing the expires= parameter to a defined value in 200 OK responses to REGISTERs

  2. by changing the expires= parameter to a defined value in 200 OK responses to INVITEs

  3. by issuing PINGs to the endpoint#39;s NAT address

  4. by sending Address Resolution Protocol (ARP) requests at a defined frequency

  5. by sending messages at a defined frequency

Answer: D

Question No: 38

In which two ways can you remove support for telnet from a media interface? (Choose two.)

  1. Navigate to the network-interface configuration element and run the delete-hip-ip lt;IP addressgt; command.

  2. Navigate to the phy-interface configuration element and run the remove-hip-ip lt;IP addressgt; command.

  3. Navigate to the network-interface configuration element and run the remove-telnet-ip

    lt;IP addressgt; command.

  4. Navigate to the network-interface configuration element and run the remove-hip-ip lt;IP addressgt; command.

  5. Navigate to the phy-interface configurationelement and run the remove-telnet-ip lt;IP addressgt; command.

Answer: A,C

Question No: 39

You are configuring a network interface to enable the Session Border Controller to use the interface for signaling and media.

Identify two valid configuration steps for supporting VLAN 12 (Choose two.)

  1. Navigate to the network-interface configuration element and set the sub-port-id parameter to 12.

  2. Navigate to the network-interface configuration element and set the sub-port-id parameter to 0.

  3. Navigate to the phy-interface configuration element and configure the hip-id parameter.

  4. Navigate to the phy-interface configuration element and configure the pri-utility-address parameter.

  5. Navigate to the network-interface configuration element and configure the name parameter.

Answer: A,C

Question No: 40

You are configuring a sip-interface configuration element. You encounter the error message: Error 409 saving configuration SipInterface.

Identify the cause of the error.

  1. You are creating a sip-port element with the same address parameter value of another sip-port.

  2. You are creating a sip-port element with the same port parameter value of another sip- port.

  3. You are creating a sip-port element with the same transport-protocol parameter value of another sip-port.

  4. You are creating a sip-interface element with the same realm-id parameter value of another sip-interface.

  5. You are creating a sip-interface element with a different realm-id parameter value of another sip-interface.

Answer: B

100% Free Download!
Download Free Demo:1z0-404 Demo PDF
100% Pass Guaranteed!
Download 2018 Latesttests 1z0-404 Full Exam PDF and VCE

Latesttests ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2018 Latesttests IT Certification PDF and VCE

Leave a Comment

(0 Comments)

Your email address will not be published. Required fields are marked *