[Free] 2018(Jan) Latesttests Passguide Oracle 1z0-404 Dumps with VCE and PDF 41-50

Latesttests
2018 Jan Oracle Official New Released 1z0-404
100% Free Download! 100% Pass Guaranteed!
http://www.Latesttests.com/1z0-404.html

Oracle Communications Session Border Controller 7 Basic Implementation Essentials

Question No: 41

You used the no command to delete a configuration element. Whichstatement is true?

  1. The deletion is lost on immediate reboot.

  2. The deletion is reflected when viewing the running configuration.

  3. The deletion takes effect immediately in the saved configuration.

  4. The deletion always requires a reboot to take effect.

  5. The deletion requires auto-save enabled.

Answer: A

Question No: 42

Which configuration step is correct for a phy-interface configuration element used for signaling and/or media?

  1. A phy-interface elementmust be configured for each interface used for High Availability (HA) heartbeats, but not for signaling and/or media.

  2. After configuring a phy-interface configuration element for signaling and/or media, a reboot of the Session Border Controller is required.

  3. A phy-interface configuration element must be configured for each interface used.

  4. A unique phy-interface configuration element is created for all signaling/media interfaces.

  5. A phy-interface configuration element for signaling and/or media hasthe operation-type parameter set to control.

Answer: B

Question No: 43

Upon issuing the done command, you getan Error 409. Which two options explain this error? (Choose two.)

  1. You are trying to create an element with a unique identifier that already exists.

  2. The configuration element you are creating is corrupted.

  3. The element you are trying to save doesnot exist.

  4. There is an internal server error.

  5. You are trying to create a second instance of a single-instance configuration element.

Answer: A,E

Question No: 44

You are examining a SIP packet. There is no final response to the ACK method. What is the reason for this?

  1. The ACK method was defined only in RFC 2543and it has been deprecated.

  2. The ACK method is part of the INVITE transaction.

  3. The ACK method is an exception in RFC 3261.

  4. The ACK method is an optional SIP method.

  5. The ACK method was replaced with the CANCEL method in RFC 3261.

Answer: B

Question No: 45

Which statement is true about Session Border Controller architectures andrealm bridging?

  1. The Hosted NAT Traversal (HNT) architecture focuses on the border point between two different service provider networks, both in the home realm.

  2. The Hosted IP architecture focuses on the border point between one enterprise network realm and one service provider network realm.

  3. The Access-backbone architecture focuses on the border point between two backbone realms.

  4. The Peering architecture focuses on the border point between two different service provider networks and theirrealms.

  5. The Gateway architecture Focuses on the border point between one enterprise network realm and one service provider network realm.

Answer: B

Question No: 46

You are troubleshooting a SIP routing issue and you haveaccess to the SIP call ow processed by the Session Border Controller.

Which two steps are valid for troubleshooting this type of issues? (Choose two.)

  1. It is necessary to locate the SIP session to troubleshoot and check if there is a 404 Routes Not Found SIP error message.

  2. It is recommended to look for 183 Session Progress SIP error messages that indicate routing issues.

  3. It is recommended to check the called number by looking at the Request-URI of the INVITE message and making sure it is a validnumber to be routed.

  4. It is recommended to find the CANCEL method received by the Session Border Controller which typically identifies a SIP routing issue.

  5. It is necessary to find an initial INVITE received by the Session Border Controller which getsa 503 Service Unavailable SIP error message.

Answer: B,E

Question No: 47

You are configuring the boot parameters in the Session Border Controller. Which three statements are true about the boot parameters? (Choose three.)

  1. A reboot is always required to apply any change to the boot parameters.

  2. The target name is usedfor domain name resolution.

  3. The system clock is a boot parameter.

  4. The boot parameters are stored in Non-Volatile Random Access Memory (NVRAM).

  5. The boot parameters are not affected by the activate-config command.

Answer: A,C,D

Question No: 48

Which three statements are true about the bootloader? (Choose three.)

  1. It decompresses the image file and loads it into the main RAM

  2. It reads the imagefile

  3. It is based on Linux

  4. It looks at the boot parameters

  5. It is a Windriver’s VxWork product

Answer: A,B,D

Question No: 49

You are configuring access rules in a Session Border Controller Peering architecture. Which configuration step is required to allow access from any User Agent (UA)?

  1. Navigate to thesip-port configuration element and set the allow-anonymous parameter to all.

  2. Navigate to the realm-config configuration element and set the addr-prefix parameter to the IP subnet of your trusted User Agent (UA).

  3. Navigate to the sip-port configurationelement and set the allow-anonymous parameter to address-prefix.

  4. Navigate to the session-agent configuration element and set the ip-address parameter to the IP subnet of your trusted User Agent (UA).

  5. Navigate to the sip-port configuration element and set the allow-anonymous parameter to agents-only.

Answer: A

Question No: 50

The Session Border Controller needs to be configured to act as a Back-to-Back User Agent (B2BUA).

How would you accomplish this?

  1. Navigate to the sip-config configuration element and set the operation-mode to stateless.

  2. Navigate to the sip-configconfiguration element and set the operation-mode to dialog.

  3. Navigate to the sip-config configuration element and set the operation-mode to stateful.

  4. Navigate to the session-router configuration element and set the operation-mode to

Answer: B

100% Free Download!
Download Free Demo:1z0-404 Demo PDF
100% Pass Guaranteed!
Download 2018 Latesttests 1z0-404 Full Exam PDF and VCE

Latesttests ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2018 Latesttests IT Certification PDF and VCE

Leave a Comment

(0 Comments)

Your email address will not be published. Required fields are marked *